How To Set Up An Ozark Trail Tent

ASSEMBLY INSTRUCTIONS

MODEL W51ane.1 DOME TENT 9' X vii'

STEP 1: Spread tent out apartment, flooring side down.

Stride ii: Extend the fiberglass frame poles by pulling out each department and placing

ends into the metal ferdominion connectors. You will have three poles. The two longer

poles are the tent poles and the shorter pole is for the wing.

Stride 3: Slide each fiberglass tent pole (A) through the sleeves on the top of

the tent roof.

Lay the fiberglass frame sections across

the tent forming an "10".

Straighten sleeves forth the

fiberglass frame

pole sections.

STEP 4: Starting at the bacchiliad of the tent, insert the fiberglass

frame poles into the pin ring located at each

corner of the tent. To raise tent, repeat the same procedure

at the front end corners of the tent, flex the fiberglass poles

into an upward position, forming ii arches.

Notation: As poles are raised, make sure metal ferrules do non catch on

the sleeves.

Pace 5: Locate the fabric ties attached to the center of the tent roof and tie

effectually the poles.

IMPORTANT: Nosotros ADVISE YOU TO ASSEMBLE THE TENT One time BEFORE

GOING CAMPING TO BECOME FAMILIAR WITH THE ASSEMBLY OF THE

TENT.

NOTE: PLEASE FiftyOOK AT THE REPLACEMENT PARTS DIAGRAM TO SEE HOW

YOUR FRAME IS ASSEMBLED.

TO PROLONG THE LIFE OF THE TENT FLOOR, SELECT A LEVEL, CLEAN Surface area

FOR THE CAMPSITE. TO PREVENT DAMAGE TO THE Zipper, UNZIP THE DOOR

TO ALLOW AIR TO ENTER THE TENT.

TO IMPROVE THE WEATHER RESISTANCE OF YOUR TENT, Information technology IS ADVIS-

ABLE TO USE SEAM SEALER TO COAT ALL EXPOSED SEAMS. YOU

SHOULD APPLY ONLY TO THE UNDERSIDE OF THE FLY AND Within

SEAMS OF THE TENT. IF Practical TO THE OUTSIDE OF SEAMS,

DISCOLORATION OF YOUR TENT MAY OCCUR. SEAM SEALER IS

AVAILABLE IN THE CAMPING Section OF ANY LOCAL SPORTINGrand

GOODS Shop.

STEP 6: Stake practicewn tent past inserting tent due southtakes through the pin band at each corner

of the tent. Hammer stakes into ground at a 45° angle, by using a hammer or mallet.

Make sure to pull tent out even

and tight.

Tent should

appear as

shown.

STEP 7: Unfold the wing. Place fly over the tent and

attach the hooks on the fly to the pivot rings at the

tent corners.

Notation: When placing the fly on the tent brand sure the pole sleeve on the wing is

located over the front door.

WARNING: Elastic cords tin snap back and striking your eydue east.

To reduce the risk of injury to you and others:

• Grandeep your body and face clear.

• Exercise not over stretch rubberband cords.

• Maintain business firm grip on claw.

• Pull the claw toward you; if information technology slips it will bound away from you.

• Make sure claw is fully clipped to tent earlier releasing.

• Wear protective eyewear during tent assembly.

Your failure to follow this warning could crusade serious injury or

permanent disability.

Footstep 9: Insert the fly pole into the sleeve at the very front end border of the fly, over the

front door. Flex the fiberglass wing pole and insert each end into the reinforced metal

grommets located on either side of the front door.

STEP 10:

Guy lines are fastened to each side & rear of fly

for additional stability. Extend the guy line and make

a loop at the opposite stop by using the slider

(as shown) and identify loop over stake. Adjust slider

to brand guy line tight and stake to the ground.

Repeat this footstep with the 2 remaining guy lines.

Tent should

appear as

shown.

NOTE: There is an attached mud mat that should be unfolded in front end of the tent door to

help keep your tent floor clean.

A mesh gear loft is included with your tent to adhere to the tent ceiling to hold small

camping items within easy accomplish.

NOTE: To take down tent, follow steps above in the repoetry order. Be sure to leave

door and windowsouth unzipped. Identify stakes into stake bag and poles into pole handbag,

which are provided. The tent should be folded into equal parts toward the center

of the tent to distribute the bulk. Fold fly and lay on top of tent. Start a pocket-sized tight

whorl, the width of the carry handbag, with the pole purse placed at the end opposite the

door. Scroll tent toward door to let air to escape. Once rolled, tie a string or rope

around tent to hold into identify. Place tent, frame and stakes into carry bag. MAKE Sure

TENT IS Clean AND DRY BEFORE STORING.

Step viii: Fasten the Velcro fasteners sewn to the edge of the wing effectually the

fiberglass tent poles.

Source: https://www.manualshelf.com/manual/ozark-trail/w511-1s/user-manual-english.html

Share this post